Machine Screws |
|||
| Size | Lengths | Uses and Comments | Picture |
| #4-40 | 1/2" 5/8" 1" |
#4-40 is being phased out | 
|
| #6-32 | 1/2" 3/4" 1" 1 1/2" |
Threads nicely into edge of 1/4" Al bar stock | |
| #8-32 | 1/2" 3/4" |
||
| #10-32 | 1/2" 1" 1 1/2" 2" |
Fits threads on Bosch Motor | |
| 1/4-20 | 1 1/2" 2" 2 1/2" |
||
| M6.0-1.00 | 16 mm 15 mm |
Flat Head - Ford Motor
mounting Hex Head - Ford Motor mounting |
|
| M3.0-0.50 | 15 mm | Rotary Pneumatic Acutator mounting | |
| M2.5-0.45 | 6 mm 10 mm |
B & D Screwdriver
Motor mounting (w/o gearhead) Sliver Maxon Motor mounting |
|
| M2.0-0.40 | 5 mm 8 mm |
Green Maxon Motor mounting Socket Head Cap Screw - Easter Egg mounting ;-) |
|
Set Screws |
|||
| Size | Length | Uses and Comments | Picture |
| #4-40 | 1/4" | Set Screws are NOT in the Fastener Cabinet. Request from you section instructor. |  |
| #6-32 | 1/4" | ||
| #10-32 | 3/8" | ||
Sheet Metal Screws |
|||
| Size | Length | Uses and Comments | Picture |
| #2 | 1/2" | Easter Egg mounting ;-) | 
|
| #4 | 1/2" | ||
| #6 | 1/2" 3/4" |
||
Nuts |
|||
| Size | Height | Uses and Comments | Picture |
| #4-40 | Full | #4-40 being phased out |  |
| #6-32 | Full | ||
| #8-32 | Full | ||
| #10-32 | Full | Fits Bosch Motor shaft | |
| 1/4-20 | Full | ||
| 3/4-16 | Half | Fits Solenoid thread | |
| M8.0-1.00 | Half | Fits Pnuematic Piston thread | |
| M4-0.70 | Full | Fits Pneumatic Piston Rod thread | |
Washers |
|||
| Size | Material | Uses and Comments | Picture |
| #4 | Zinc Plated Steel | #4-40 is being phased out |  |
| #6 | Zinc Plated Steel Nylon |
||
| #8 | Zinc Plated Steel | ||
| #10 | Zinc Plated Steel Nylon |
||
| 1/4-20 | Zinc Plated Steel Nylon |
||
Spring Pins |
|||
| Diameter | Length | Uses and Comments | Picture |
| 1/8" | 1/4" | Gear retention or Pneumatic Piston Clevis |  |
| 1/8" | 1/2" | Gear retention | |
| 1/8" | 3/4" | Gear retention | |
| 1/8" | 1" | Gear retention | |
Pop Rivets |
|||
| Body Diameter | Grip Range | Uses and Comments | Picture |
| 1/8" | 0.126"-0.187" |  |
|
| 1/8" | 0.188"-0.250" | ||
Hose Clamps |
|||
| Clamping Range | Width | Uses and Comments | Picture |
| 9/16" to 1 1/16" | 1/2" |  |
|
| 1 1/16" to 2" | 1/2" | Mounting the B & D Screwdriver Motor | |
All data is in appropriate units. Millimeters for metric fasteners, inches for english fasteners.
All machine screws are slot pan head (soon to be phillips pan head) unless otherwise specified.